Ral Color Gloss Smooth Texture Epoxy Polyester Powder Coatings
Powder coatings are mixed with a certain proportion of the resin, fillers, curing agents and other additives, then prepared by hot extrusion ,crushed and sieved.The products are stable at room temperature storage, then baking heat melted and solidified to form a smooth and bright permanent coating to achieve the purpose of decoration and corrosion.
1).The products are non-toxic, solvent-free and non-toxic volatile substances,
there are no intoxication, no fire, no "three wastes" emissions and other pollution problems, in full compliance with national environmental laws.
2).Raw material utilization is high, the highest utilization rate even more than
3).After being pre-coated handle, disposable construction, without primer,
you can get a sufficient thickness of the coating, easy to automate operation, high production efficiency, reduce costs.
4).Dense coating adhesion, good impact strength and toughness, high
coverage corners, with excellent resistance to chemical corrosion and electrical insulation properties.
5).Powder coatings storage and transport are safety and convenience.
The products include high light ( above 86%),glazed (76%-85%),matte(20%-50%),low light (below 20%). We also offer a variety of shiny products according to the needs of users.
4.Powder physical properties:
Proportion : 1.2-1.8 (depending on the color and gloss ) .
Particle size distribution: 100% less than 125 microns (more than 85% between 60 to 90).
Curing conditions:200°C,10 minutes.
8-10m³/kg, the membrane is 60μm
(calculate by 100% utilization rate of powder coating).
Carton packaging, lined with double polyethylene bag, net weight 25 kg.
7.Storage requirements: Store below 30 °C, ventilated, dry, clean room, not near the fire, heat, direct sunlight, open dumps is prohibited.Under this condition, the powder can be stable for 12 months, more than the storage period may be re-examined, such as the results meet the requirements, can still be used.
8.Health and safety:
This product is non-toxic. In the course of inhalation of dust should be avoided. The operators should wear appropriate dust mask and glasses.
|The adhesion (grid method)
|Salt spray test
|Damp heat test
||Good gloss retention,E≤0.3-0.4
|Florida weathering exposure
||South 45 °,12mons
|Artificial accelerated aging
||60°C/8hours + 50°C/4hours condensing,cycle for 500hours
||Gloss retention≥50% Color stability:E≤0.35
||1.The above experiment uses 0.8mm steel with degreasing and rusting, and the coating thickness are 50-70 microns.
||2.The above coating performance may be lower as shiny and slightly lower.
11.Why choose our products?
1). We have our own factory. The good quality and the competitive is the advantage of our company.
2). The material we choose is always good and products always come out with high quality.
3). A trial order or sample orders are welcomed.
4). Our products are exported to Europe, America, Southeast Asia, and other countries and regions in the world.
5). We will do our best to service you all the time if you have the further question.
12 . FAQ
(1) What powder we can manufacture?
We can do almost all the RAL and PANTONE colors;
We can do almost all the finish powder, like smooth, texture, structure etc.
We can do a lot of special powders, like conductive powder, Insulation powder, Soft touch powder, Anti-graffitti powder, Zinc-Rich powder, super thin powder etc.
(2) Our Packing: 25kg / box
Box Size: 40 * 25 * 33 cm (L * W * H)
Pallet size: 1.1 * 1.16m Material: Plywood
(3) Our MOQ: Usually 200kg/ Color
(4) Delivery Time: Usually send out the goods within 1~ 15 days.
(5) Can we get some samples from you?
Yes, we can supply you 1-2 kg powder samples for your testing, but we need you to pay the freight firstly.
(6) How can we get the quotation?
Please send us your technical data or let us know your requirement as following: Color, Powder Type, Gloss, Surface and other performance requirements .